What is Resistor? | Resistor Kya Hai?

Resistor

Resistor

 

What is a Resistor?

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.

Resistors are common elements of electrical networks and electronic circuits and are ubiquitous in electronic equipment. Practical resistors as discrete components can be composed of various compounds and forms. Resistors are also implemented within integrated circuits.

The electrical function of a resistor is specified by its resistance: common commercial resistors are manufactured over a range of more than nine orders of magnitude. The nominal value of the resistance falls within the manufacturing tolerance, indicated on the component.

A resistor is an electrical component that limits or regulates the flow of electrical current in an electronic circuit. Resistors can also be used to provide a specific voltage for an active device such as a transistor.

Resistors can be fabricated in a variety of ways. The most common type in electronic devices and systems is the carbon-composition resistor. Fine granulated carbon (graphite) is mixed with clay and hardened. The resistance depends on the proportion of carbon to clay; the higher this ratio, the lower the resistance.All other factors being equal, in a direct-current (DC) circuit, the current through a resistor is inversely proportional to its resistance, and directly proportional to the voltage across it. This is the well-known Ohm's Law. In alternating-current (AC) circuits, this rule also applies as long as the resistor does not contain inductance or capacitance.

Another type of resistor is made from winding Nichrome or similar wire on an insulating form. This component, called a wirewound resistor, is able to handle higher currents than a carbon-composition resistor of the same physical size. However, because the wire is wound into a coil, the component acts as an inductors as well as exhibiting resistance. This does not affect performance in DC circuits, but can have an adverse effect in AC circuits because inductance renders the device sensitive to changes in frequency.

Electronic symbols and notation:-

  (A) Fixed resistor:-

1. Lead arrangements:- Through-hole components typically have "leads" (pronounced \ˈlēdz\) leaving the body "axially," that is, on a line parallel with the part's longest axis. Others have leads coming off their body "radially" instead. Other components may be SMT (surface mount technology), while high power resistors may have one of their leads designed into the heat sink.

2. Carbon composition:- Carbon composition resistors consist of a solid cylindrical resistive element with embedded wire leads or metal end caps to which the lead wires are attached. The body of the resistor is protected with paint or plastic. Early 20th-century carbon composition resistors had uninsulated bodies; the lead wires were wrapped around the ends of the resistance element rod and soldered. The completed resistor was painted for color-coding of its value.

The resistive element is made from a mixture of finely powdered carbon and an insulating material, usually ceramic. A resin holds the mixture together. The resistance is determined by the ratio of the fill material (the powdered ceramic) to the carbon. Higher concentrations of carbon, which is a good conductor, result in lower resistance. Carbon composition resistors were commonly used in the 1960s and earlier, but are not popular for general use now as other types have better specifications, such as tolerance, voltage dependence, and stress. Carbon composition resistors change value when stressed with over-voltages. Moreover, if internal moisture content, from exposure for some length of time to a humid environment, is significant, soldering heat creates a non-reversible change in resistance value. Carbon composition resistors have poor stability with time and were consequently factory sorted to, at best, only 5% tolerance.These resistors, however, if never subjected to overvoltage nor overheating were remarkably reliable considering the component's size.

Carbon composition resistors are still available, but comparatively quite costly. Values ranged from fractions of an ohm to 22 megohms. Due to their high price, these resistors are no longer used in most applications. However, they are used in power supplies and welding controls.

3. Carbon pile:- A carbon pile resistor is made of a stack of carbon disks compressed between two metal contact plates. Adjusting the clamping pressure changes the resistance between the plates. These resistors are used when an adjustable load is required, for example in testing automotive batteries or radio transmitters. A carbon pile resistor can also be used as a speed control for small motors in household appliances (sewing machines, hand-held mixers) with ratings up to a few hundred watts. A carbon pile resistor can be incorporated in automatic voltage regulators for generators, where the carbon pile controls the field current to maintain relatively constant voltage.The principle is also applied in the carbon microphone.

4. Carbon film:- A carbon film is deposited on an insulating substrate, and a helix is cut in it to create a long, narrow resistive path. Varying shapes, coupled with the resistivity of amorphous carbon (ranging from 500 to 800 μΩ m), can provide a wide range of resistance values. Compared to carbon composition they feature low noise, because of the precise distribution of the pure graphite without binding. Carbon film resistors feature a power rating range of 0.125 W to 5 W at 70 °C. Resistances available range from 1 ohm to 10 megohm. The carbon film resistor has an operating temperature range of −55 °C to 155 °C. It has 200 to 600 volts maximum working voltage range. Special carbon film resistors are used in applications requiring high pulse stability

5. Printed carbon resistor:-  Carbon composition resistors can be printed directly onto printed circuit board (PCB) substrates as part of the PCB manufacturing process. Although this technique is more common on hybrid PCB modules, it can also be used on standard fibreglass PCBs. Tolerances are typically quite large, and can be in the order of 30%. A typical application would be non-critical pull-up resistors.

6. Thick and thin film:- Thick film resistors became popular during the 1970s, and most SMD (surface mount device) resistors today are of this type. The resistive element of thick films is 1000 times thicker than thin films,^[11] but the principal difference is how the film is applied to the cylinder (axial resistors) or the surface (SMD resistors).

Thin film resistors are made by sputtering (a method of vacuum deposition) the resistive material onto an insulating substrate. The film is then etched in a similar manner to the old (subtractive) process for making printed circuit boards; that is, the surface is coated with a photo-sensitive material, then covered by a pattern film, irradiated with ultraviolet light, and then the exposed photo-sensitive coating is developed, and underlying thin film is etched away.

Thick film resistors are manufactured using screen and stencil printing processes.

Because the time during which the sputtering is performed can be controlled, the thickness of the thin film can be accurately controlled. The type of material is also usually different consisting of one or more ceramic (cermet) conductors such as tantalum nitride (TaN), ruthenium oxide (RuO
2), lead oxide (PbO), bismuth ruthenate (Bi
2Ru
2O
7), nickel chromium (NiCr), or bismuth iridate (Bi
2Ir
2O
7).

The resistance of both thin and thick film resistors after manufacture is not highly accurate; they are usually trimmed to an accurate value by abrasive or laser trimming. Thin film resistors are usually specified with tolerances of 0.1, 0.2, 0.5, or 1%, and with temperature coefficients of 5 to 25 ppm/K. They also have much lower noise levels, on the level of 10–100 times less than thick film resistors.^{[citation needed]}

Thick film resistors may use the same conductive ceramics, but they are mixed with sintered (powdered) glass and a carrier liquid so that the composite can be screen-printed. This composite of glass and conductive ceramic (cermet) material is then fused (baked) in an oven at about 850 °C.

Thick film resistors, when first manufactured, had tolerances of 5%, but standard tolerances have improved to 2% or 1% in the last few decades. Temperature coefficients of thick film resistors are high, typically ±200 or ±250 ppm/K; a 40 kelvin (70 °F) temperature change can change the resistance by 1%.

Thin film resistors are usually far more expensive than thick film resistors. For example, SMD thin film resistors, with 0.5% tolerances, and with 25 ppm/K temperature coefficients, when bought in full size reel quantities, are about twice the cost of 1%, 250 ppm/K thick film resistors.

7. Metal film:- A common type of axial-leaded resistor today is the metal-film resistor. Metal Electrode Leadless Face (MELF) resistors often use the same technology, and are also cylindrically shaped but are designed for surface mounting. Note that other types of resistors (e.g., carbon composition) are also available in MELF packages.

Metal film resistors are usually coated with nickel chromium (NiCr), but might be coated with any of the cermet materials listed above for thin film resistors. Unlike thin film resistors, the material may be applied using different techniques than sputtering (though this is one of the techniques). Also, unlike thin-film resistors, the resistance value is determined by cutting a helix through the coating rather than by etching. (This is similar to the way carbon resistors are made.) The result is a reasonable tolerance (0.5%, 1%, or 2%) and a temperature coefficient that is generally between 50 and 100 ppm/K.^[12] Metal film resistors possess good noise characteristics and low non-linearity due to a low voltage coefficient. Also beneficial are their tight tolerance, low temperature coefficient and long-term stability.

8. Metal oxide film:- Metal-oxide film resistors are made of metal oxides which results in a higher operating temperature and greater stability/reliability than Metal film. They are used in applications with high endurance demands.

9. Wire wound:- Wirewound resistors are commonly made by winding a metal wire, usually nichrome, around a ceramic, plastic, or fiberglass core. The ends of the wire are soldered or welded to two caps or rings, attached to the ends of the core. The assembly is protected with a layer of paint, molded plastic, or an enamel coating baked at high temperature. These resistors are designed to withstand unusually high temperatures of up to 450 °C.^[7] Wire leads in low power wirewound resistors are usually between 0.6 and 0.8 mm in diameter and tinned for ease of soldering. For higher power wirewound resistors, either a ceramic outer case or an aluminum outer case on top of an insulating layer is used – if the outer case is ceramic, such resistors are sometimes described as "cement" resistors, though they do not actually contain any traditional cement. The aluminum-cased types are designed to be attached to a heat sink to dissipate the heat; the rated power is dependent on being used with a suitable heat sink, e.g., a 50 W power rated resistor overheats at a fraction of the power dissipation if not used with a heat sink. Large wirewound resistors may be rated for 1,000 watts or more.

Because wirewound resistors are coils they have more undesirable inductance than other types of resistor, although winding the wire in sections with alternately reversed direction can minimize inductance. Other techniques employ bifilar winding, or a flat thin former (to reduce cross-section area of the coil). For the most demanding circuits, resistors with Ayrton-Perry winding are used.

Applications of wirewound resistors are similar to those of composition resistors with the exception of the high frequency. The high frequency response of wirewound resistors is substantially worse than that of a composition resistor.

10. Foil resistor:- The primary resistance element of a foil resistor is a special alloy foil several micrometers thick. Since their introduction in the 1960s, foil resistors have had the best precision and stability of any resistor available. One of the important parameters influencing stability is the temperature coefficient of resistance (TCR). The TCR of foil resistors is extremely low, and has been further improved over the years. One range of ultra-precision foil resistors offers a TCR of 0.14 ppm/°C, tolerance ±0.005%, long-term stability (1 year) 25 ppm, (3 years) 50 ppm (further improved 5-fold by hermetic sealing), stability under load (2000 hours) 0.03%, thermal EMF 0.1 μV/°C, noise −42 dB, voltage coefficient 0.1 ppm/V, inductance 0.08 μH, capacitance 0.5 pF.^[

11. Ammeter shunts:- An ammeter shunt is a special type of current-sensing resistor, having four terminals and a value in milliohms or even micro-ohms. Current-measuring instruments, by themselves, can usually accept only limited currents. To measure high currents, the current passes through the shunt across which the voltage drop is measured and interpreted as current. A typical shunt consists of two solid metal blocks, sometimes brass, mounted on an insulating base. Between the blocks, and soldered or brazed to them, are one or more strips of low temperature coefficient of resistance (TCR) manganin alloy. Large bolts threaded into the blocks make the current connections, while much smaller screws provide volt meter connections. Shunts are rated by full-scale current, and often have a voltage drop of 50 mV at rated current. Such meters are adapted to the shunt full current rating by using an appropriately marked dial face; no change need to be made to the other parts of the meter.

12. Grid resistor:- In heavy-duty industrial high-current applications, a grid resistor is a large convection-cooled lattice of stamped metal alloy strips connected in rows between two electrodes. Such industrial grade resistors can be as large as a refrigerator; some designs can handle over 500 amperes of current, with a range of resistances extending lower than 0.04 ohms. They are used in applications such as dynamic braking and load banking for locomotives and trams, neutral grounding for industrial AC distribution, control loads for cranes and heavy equipment, load testing of generators and harmonic filtering for electric substations.

The term grid resistor is sometimes used to describe a resistor of any type connected to the control grid of a vacuum tube. This is not a resistor technology; it is an electronic circuit topology.

(B)  Variable Resistors:-

Adjustable resistors:-  A resistor may have one or more fixed tapping points so that the resistance can be changed by moving the connecting wires to different terminals. Some wirewound power resistors have a tapping point that can slide along the resistance element, allowing a larger or smaller part of the resistance to be used.

Where continuous adjustment of the resistance value during operation of equipment is required, the sliding resistance tap can be connected to a knob accessible to an operator. Such a device is called a rheostat and has two terminals.

Potentiometers:- A potentiometer or pot is a three-terminal resistor with a continuously adjustable tapping point controlled by rotation of a shaft or knob or by a linear slider. It is called a potentiometer because it can be connected as an adjustable voltage divider to provide a variable potential at the terminal connected to the tapping point. A volume control for an audio device is a common use of a potentiometer. A typical low power potentiometer (see drawing) is constructed of a flat resistance element (B) of carbon composition, metal film, or conductive plastic, with a springy phosphor bronze wiper contact (C) which moves along the surface. An alternate construction is resistance wire wound on a form, with the wiper sliding axially along the coil. These have lower resolution, since as the wiper moves the resistance changes in steps equal to the resistance of a single turn.

High-resolution multiturn potentiometers are used in a few precision applications. These have wirewound resistance elements typically wound on a helical mandrel, with the wiper moving on a helical track as the control is turned, making continuous contact with the wire. Some include a conductive-plastic resistance coating over the wire to improve resolution. These typically offer ten turns of their shafts to cover their full range. They are usually set with dials that include a simple turns counter and a graduated dial, and can typically achieve three digit resolution. Electronic analog computers used them in quantity for setting coefficients, and delayed-sweep oscilloscopes of recent decades included one on their panels.

Resistance decade boxes:- A resistance decade box or resistor substitution box is a unit containing resistors of many values, with one or more mechanical switches which allow any one of various discrete resistances offered by the box to be dialed in. Usually the resistance is accurate to high precision, ranging from laboratory/calibration grade accuracy of 20 parts per million, to field grade at 1%. Inexpensive boxes with lesser accuracy are also available. All types offer a convenient way of selecting and quickly changing a resistance in laboratory, experimental and development work without needing to attach resistors one by one, or even stock each value. The range of resistance provided, the maximum resolution, and the accuracy characterize the box. For example, one box offers resistances from 0 to 100 megohms, maximum resolution 0.1 ohm, accuracy 0.1%.

..................................................................................................................................................

New Intro Video | Naya Intro Video

League of Angels | 2K17 New Gameplay |

How to Live Stream on YouTube | Start to Finish | Using OBS

In this Video I'm showing you, how to setup a professional looking live stream on YouTube using software that is free and open source, By using OBS (Open Broadcaster Software) . 

Download OBS (Open Broadcaster Software) -   

http://obsproject.com

Facebook Page - https://www.facebook.com/scienceandtechnologicaldevelopment/

Facebook Self- https://www.facebook.com/king.anupam.dutta/

Twitter- https://twitter.com/kinganupamdutta

Google Plus- https://plus.google.com/u/0/+KingAnupamDutta

Google Plus-https://plus.google.com/u/1/106994625573309165657

Blog- https://kinganupamdutta.blogspot.com/

Blog- http://kingsallinone.blogspot.com/

Disclaimer- Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use.

All rights reserved to Playweb Games Inc. We do not own this game, Playweb Games Inc. owns that privilege.

Fair Use

Additionally, the fair use defense to copyright infringement was codified for the first time in section 107 of the 1976 Act. Fair use was not a novel proposition in 1976, however, as federal courts had been using a common law form of the doctrine since the 1840s (an English version of fair use appeared much earlier). The Act codified this common law doctrine with little modification. Under section 107, the fair use of a copyrighted work is not copyright infringement, even if such use technically violates section 106. While fair use explicitly applies to use of copyrighted work for criticism, news reporting, teaching, scholarship, or research purposes, the defense is not limited to these areas. The Act gives four factors to be considered to determine whether a particular use is a fair use:

the purpose and character of the use (commercial or educational, transformative or reproductive);

the nature of the copyrighted work (fictional or factual, the degree of creativity); 

the amount and substantiality of the portion of the original work used; and

the effect of the use upon the market (or potential market) for the original work.

Police Lights using 555 Timer IC

Police Lights using 555 Timer IC

This circuit simulates the police car lights by alternate flashing. This circuit flashes red LED s for three times and blue LED’s for three times. This flashing action performs continuously.

This circuit uses 555 timer and a decade counter. Here, 555 timer runs in astable mode. Decade counter 4017 counts the incoming pulses that is for first pulse Q0 becomes high and for second pulse Q1 becomes high and so on again for 10th pulse Q0 state becomes high.

Circuit Diagram of Police Lights using 555 IC:-

Electronic Ingredients for Circuit :-

• NE555 timer
• 4017 decade counter
• 1n4148 diodes – 6
• 1k Resistor(1/4 watt) – 1
• 22k Resistor(1/4 watt) – 1
• 470 ohm Resistor(1/4 watt) – 8
• 2.2uF Electrolytic capacitor(16V or 25V) – 1
• Blue LED’s – 2
• Red LED’s – 2
• 9v battery – 1
• Connecting wires
• 
  

555 IC :- Here 555 timer runs in free running mode. It produces pulses whose width can be varied. 2nd and 6th pins are shorted to allow triggering after every cycle. 4th pin is connected to Vcc to avoid sudden resets.

4017 IC :- It is a 10 bit counter with ten decoded outputs. It counts the incoming pulses. The supply voltage range is -0.5 to +22V. The high pulse on the reset pin clears the count to zero. The speed of operation of this IC is up to 10 Mhz. The ouput states (Q0,Q2,Q4) are ORed to flash the blue LED’s 3 times and the states Q5, Q7 and Q9 are ORed to flash the red LED’s 3 times. Based on the outputs of 4017 IC, two transistors (NPN) switches the LED’s ON and OFF. Resistors R3, R4, R5, R6 are used to protect the LED’s from high voltage.

NOTE- Make this project on your home and you can increase the number of led lights using multiple transistors like BC547

Stay Tuned with King's All in One Technology & Science & KingAnupamDutta

Oneplus 3

     

OnePlus 3

• 16MP primary camera (f/2.0 Aperture, 1.12 µm Pixels) with high speed autofocus technology (PDAF), Electronic (EIS) and Optical (OIS) stabilization technologies and 8MP front facing camera,Corning's Gorilla Glass 4
• 
  
• 13.97 centimeters (5.5-inch) Optic AMOLED capacitive touchscreen with full HD (401 ppi) 1920 x 1080 pixels resolution; ceramic-coated fingerprint Scanner (<0.2 seconds)
• 
  
• OxygenOS based on Android Marshmallow 6.0.1 operating system with 2.2GHz + 1.6GHz Kryo Qualcomm Snapdragon 820 quad core processor, 14nm FinFET technology, Adreno 530 GPU, 6GB LPDDR4 RAM, 64GB internal memory (UFS 2.0 Flash Storage) and dual nano-SIM dual-standby (4G+4G) with NFC enabled and reversible type-C connector
• 
  
• 3,000 mAh lithium-polymer battery (non-removable) powered by state-of-the-art Dash Charge technology (replenish over 60% of the battery within 30 minutes)
• 
  
• 1 year manufacturer warranty for device and 6 months manufacturer warranty for in-box accessories including batteries from the date of purchase

• NETWORK	Technology	GSM / HSPA / EVDO / LTE
  	2G bands	GSM 850 / 900 / 1800 / 1900 - SIM 1 & SIM 2
  	3G bands	HSDPA 850 / 900 / 1700(AWS) / 1900 / 2100 - North America
  		HSDPA 850 / 900 / 1900 / 2100 - Global model
  		CDMA2000 1xEV-DO - North America
  	4G bands	LTE band 1(2100), 2(1900), 4(1700/2100), 5(850), 7(2600), 8(900), 12(700), 17(700), 30(2300) - North America
  		LTE band 1(2100), 3(1800), 5(850), 7(2600), 8(900), 20(800), 38(2600), 40(2300) - Global model
  	Speed	HSPA 42.2/5.76 Mbps, LTE-A (2CA) Cat6 300/50 Mbps
  	GPRS	Yes
  	EDGE	Yes

  
  

  LAUNCH	Announced	2016, June
  	Status	Available. Released 2016, June

  
  

  BODY	Dimensions	152.7 x 74.7 x 7.4 mm (6.01 x 2.94 x 0.29 in)
  	Weight	158 g (5.57 oz)
  	SIM	Dual SIM (Nano-SIM, dual stand-by)

  
  

  DISPLAY	Type	Optic AMOLED capacitive touchscreen, 16M colors
  	Size	5.5 inches (~73.1% screen-to-body ratio)
  	Resolution	1080 x 1920 pixels (~401 ppi pixel density)
  	Multitouch	Yes
  	Protection	Corning Gorilla Glass 4
  		- Oxygen OS 3.2.8

  
  

  PLATFORM	OS	Android OS, v6.0.1 (Marshmallow)
  	Chipset	Qualcomm MSM8996 Snapdragon 820
  	CPU	Quad-core (2x2.15 GHz Kryo & 2x1.6 GHz Kryo)
  	GPU	Adreno 530

  
  

  MEMORY	Card slot	No
  	Internal	64 GB, 6 GB RAM

  
  

  CAMERA	Primary	16 MP, f/2.0, phase detection autofocus, OIS, LED flash, check quality
  	Features	1/2.8" sensor size, 1.12 µm pixel size, geo-tagging, touch focus, face detection, panorama, HDR
  	Video	2160p@30fps, 1080p@30/60fps, 720p@120fps, Auto HDR, check quality
  	Secondary	8 MP, f/2.0, 1/3.2" sensor size, 1.4 µm pixel size, 1080p

  
  

  SOUND	Alert types	Vibration; MP3, WAV ringtones
  	Loudspeaker	Yes
  	3.5mm jack	Yes
  		- Active noise cancellation with dedicated mic

  
  

  COMMS	WLAN	Wi-Fi 802.11 a/b/g/n/ac, Wi-Fi Direct, DLNA, hotspot
  	Bluetooth	v4.2, A2DP, LE
  	GPS	Yes, with A-GPS, GLONASS, BDS
  	NFC	Yes
  	Radio	No
  	USB	v2.0, Type-C 1.0 reversible connector

  
  

  FEATURES	Sensors	Fingerprint (front-mounted), accelerometer, gyro, proximity, compass
  	Messaging	SMS (threaded view), MMS, Email, IM, Push Email
  	Browser	HTML5
  	Java	No
  		- Fast battery charging: 60% in 30 min (Dash Charge)  - DivX/Xvid/MP4/H.265 player - MP3/eAAC+/WMA/WAV/FLAC player - Document viewer - Photo/video editor

  
  

  BATTERY		Non-removable Li-Ion 3000 mAh battery

  
  

  MISC	Colors	Graphite, soft gold
  	SAR EU	0.39 W/kg (head)     0.32 W/kg (body)
  	Price group	7/10

  
  

  TESTS	Performance	Basemark OS II: 2677 / Basemark OS II 2.0: 2365 Basemark X: 32715
  	Display	Contrast ratio: Infinite (nominal), 4.424(sunlight)
  	Camera	Photo / Video
  	Loudspeaker	Voice 62dB / Noise 71dB / Ring 77dB
  	Audio quality	Noise -93.4dB / Crosstalk -94.4dB
  	Battery life	Endurance rating 66h